[Home ] [Archive]   [ فارسی ]  
:: Main :: About :: Current Issue :: Accepted articles :: Archive :: Search :: Submit :: Contact ::
:: Volume 6, Issue 4 (9-2019) ::
jehe 2019, 6(4): 339-355 Back to browse issues page
Efficiency and Modeling of UV-Electropersulfate Process via Iron Electrode in the Degradation of Acid Blue 25 Dye Using Central Composite Design
Mohammadreza Samarghandi, Alireza Rahmani, Ghorban Asgari, Jamal Mehralipour, Mohammad Jamil Moradi
Ms.c. Student of Environmental Health Eng., Faculty of Public Health, Hamadan University of Medical Science, Hamadan, I.R.IRAN., Research Committee(SRC)
Abstract:   (640 Views)
Background: Dyes are resistant organic matter because they have an aromatic rings. Sulfate radical (SO4●-) is a powerful oxidative radical. The design via CCD, cause the process was done by high accurate and low-cost. The aim of this study was modeling of UV-EPS process to degradation of Acid Blue 25 dye via the CCD from aqueous.
Methods: In this experiment study, used to a photoelectrochemical reactor with two iron electrodes as an anode and two titanium electrodes as a cathode and Low-pressure mercury lamp (254 nm). The pH (2-4), Direct Current (0.75-1/5 A), S2O82- concentration (0/5-1/5 mg/l), reaction time (20-40 min) and initial concentration of AB25 (50 -100 mg/l) as a main independed variables were chosen. Also, COD, synergist effect, presence of radical scavenger and kinetic of reaction were studied in optimum conditions. Dye concentration and COD were measured by spectrophotometer (DR5000).
Results: The results illustrate that the efficiency of process is affected by the variables. Optimum condition obtained in pH=3/01, DC was 1/08 A, PS was 1/30 mg/l, reaction time was 34 minute and initial concentration equal to 50 mg/l. In this situation efficiency of process was 91 percent. The COD removal in these conditions was 69 percent. The correlation coefficient was 0.84 which indicates that the quadratic model is suitable for process design. The kinetics of reaction followed the first order kinetics. Reduce of efficiency of process in the presence of radical scavenger occur.
Conclusion: Optimizing via CCD reduces the number of runs and increases accuracy. This process has a high efficiency in dye and COD removal and this process can be used to reduce the pollutant loading form industrial wastewater, such as textile wastewater, before discharging into the environment.
Keywords: Modeling, UV-Electropersulfate, Acid Blue 25 dye, Central Composite Design, Aqueous
Full-Text [PDF 1607 kb]   (224 Downloads)    
Type of Study: Research | Subject: Special
Received: 2019/09/14 | Accepted: 2019/09/14 | Published: 2019/09/14
Add your comments about this article
Your username or Email:

CAPTCHA



XML   Persian Abstract   Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Samarghandi M, Rahmani A, Asgari G, Mehralipour J, Moradi M J. Efficiency and Modeling of UV-Electropersulfate Process via Iron Electrode in the Degradation of Acid Blue 25 Dye Using Central Composite Design. jehe. 2019; 6 (4) :339-355
URL: http://jehe.abzums.ac.ir/article-1-667-en.html


Volume 6, Issue 4 (9-2019) Back to browse issues page
مجله مهندسی بهداشت محیط Journal of Environmental Health Enginering
Persian site map - English site map - Created in 0.07 seconds with 31 queries by YEKTAWEB 4075